I think you should clear codes,then see what codes come up,when you jumped the ASD,could have set codes that has nothing to do with your problem! Pulling fuse #11 should clear codes
2006 Charger RT 5.7 stalling issue, and can sensor fitting issue.
Hello I was wondering if anyone could help me, their be a topic already but it think it's only for srt, I have a rt 5.7. I tried the asd jump but it made the situation worse , cel light now showing all O2 sensors , and of course p0340 sometimes p0344 and of course all O2 sensors, esp and traction control light turns on suddenly while driving , on and off deal. Thanks in advance
1 - 9 of 21 Posts
POO31Just tried it, cleared codes till I started it gave me p0031 p0037 p0051 and engine was just shaking , did I maybe burn the tcim? The jumper is not installed at the moment , and it still shuts off and starts back up and runs a bit better
Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 harness is open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit poor electrical connection
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse
- Faulty Engine Control Module (ECM)
PO037
Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 harness is open or shorted
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Engine Control Mo e (ECM)
POO51
Faulty Heated Oxygen Sensor (H2OS) Bank 2 Sensor 1
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 1 harness is open shorted
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 1 circuit poor electrical connection
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 1 fuse
- Faulty Engine Control Module (ECM)
So according to the codes,you have both O2 sensor circuit problems on bank 1,rear sensor circuit problem on right bank.Have you done anything that would cause these codes like working on wiring or did it just start? Its hard to believe all those sensors would be bad at once,so im think a wiring problem like a short!
I think the person who originally did this,put in an off/on switch!It the only way his SRT would run!
The ASD relay!You cant leave it jumped all the time when the system is shutoff,your energizing the coils,fuel pump,injectors and that spells disaster.The person put in an On/OFF switch,so when he shut off car,the ASD relay is not energized!On and off to what?
Yes find out what causing your O2 sensor codes,I would start with looking at wiring harness,replace whats needed!Any other method other than jumping the asd relay since it already may have burned my O2 sensors
You need 2 repair what ever is causng you O2 sensors code,until then,your car wont run right because the PCM needs to reads their signals.It hasn't shut off only runs terrible when i first start it , shuts off then turn right back up no misfire or anything
Last time I talked to him he said he put in On/off switchActually, he did leave it jumped all the time. He had an SRT with a weird issue that the ASD jumper fixed. Even Chrysler told him not to do it, but they finally agreed that it worked on his car, but they didn't know why.
Doing it on a normal car fries the O2 sensors. OP, Remove the jumper and don't do it again. You now also need to replace the 02 sensors.
You need to find a way to resolve your original issue...and this isn't it.
What was it that you were trying to fix by doing this?
That could be your problem,these cars like OEM sensors!If the asd was the reason for the car to shut off, and if by jumping it if it would fix the issue, and also I diconnected an O2 sensor and the code went away, weird but I'll replace O2 sensors, so far car runs fine after the 2nd to 3rd start only showing me the 3 O2 sensor codes and the annoying p0340 , I used autozone sensors, (cam and crank) not sure if that's the problem
Po300,is usually a vacuum leak or a fuel delivery problem,PO340 is the Cam sensor circuit,Check wiring for a short of broken wire,The other codes show problem with Bank 2 Sensor 2,O2 sensor circuit,same thing check wiringReplaced all 4 O2 sensors, seemed really bad visually, still getting codes, car rarely shuts off, but runs rough with p0300 random miss, and reoccurring p0340 with p1158 and p1159, anyone might have an idea? Thanks in advance
1 - 9 of 21 Posts
- This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Charger Forums
ChargerForums to connect with the Dodge Charger community to discuss SRT, Hellcat models, maintenance, mods and more.
Full Forum Listing
Recommended Communities
